Slip the remaining compression nut and ferrule over the refrigerator end of the new water line. Turn on the cold water faucet to drain any water left in the supply line. Then you'd need to twist the valve until it pierces your water line. Twist the faucet supply line onto the female end of the adapter. Tighten the connection just slightly more than hand-tight, using pliers.
If the refrigerator has a water dispenser, flush out several gallons to purge the line of all the air. Attach the Adapt-a-Tee adapter to the shutoff valve, tightening by hand at first. Tighten the fittings as needed, using channel-type pliers or an adjustable wrench.
You are being redirected
How to Install a Water Line for a Refrigerator
Turn the water on and check for leaks. This is used to display charts and graphs on articles and the author center. She writes mainly home improvement, health and travel articles for various online publications.
Or continue shopping on Samsung. To have a water dispenser or ice maker in your fridge, you need to be able to get water from your cold water supply to your fridge in an efficient way. Braided tubing is fitted at both ends with the proper fittings, virtual online dating site so all you have to do is tighten the line to your connections.
- Use pliers to untwist the faucet supply line from the cold water supply valve.
- Learn more about Samsung promotions.
- All information included herein is subject to change without notice.
- Connect the line to the water line connector on the back of the refrigerator.
- The water lines are typically sold in kits and are not included with the refrigerator.
- In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator.
- Adapt-a-Tees can be used in many situations where you need an extra line.
- If the model has a dispenser, make sure the water filter is installed, and then dispense one gallon of water before drinking or using any water from the refrigerator.
Tighten the connections slightly if you see a leak. Shut off the water at the valve that controls the cold-water supply pipe to the faucet. Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier.
Thank you for your feedback! If there are no fixure shutoff valves, you can turn off the water by closing the main water supply valve to the entire house. If there is no water dispenser, throw away the first full batch or two of ice to make sure it is all clean and ready to use. Leave the excess water line behind the refrigerator. Other answers that might help.
Connect the water supply line to the refrigerator
If needed, you can install a booster pump to compensate for low pressure. Run the new supply tube to the back of the refrigerator. If so, your job is very easy. Disconnect the faucet supply tube from the shutoff valve. You can use the water line leftover from your previous refrigerator, or start fresh with a new kit from the hardware store.
Slip the compression nut that came with the kit over the newly installed supply line. Some articles have YouTube videos embedded in them. Connect the water supply line to the refrigerator. Do not over-tighten it, as over-tightening will cause a leak. To provide a better website experience, dengarden.
Connect and install the water line to your refrigerator
If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line. The kit provides you with the required parts to hook up a water line to your refrigerator. Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher. If running the line through the cabinets is not feasible, you might need to run a line through the floor and up to where the refrigerator is located. Push the refrigerator against the wall.
First, locate the shutoff valve under the kitchen sink where you want to connect the new water line. Redirect Notification As of Nov. No data is shared with Facebook unless you engage with this feature.
An Adapt-a-Tee is an ideal plumbing fitting for this purpose. If your home doesn't have a water line installed from a previous refrigerator, you will need a water line that can run between the water pipes in your home and your fridge. Google provides ad serving technology and runs an ad network. Coil the excess water line behind the refrigerator.
Ask the Community Browse answers, ask questions and get solutions from other Samsung customers. This is used to collect data on traffic to articles and other pages on our site. Questions must be on-topic, written with proper grammar usage, and understandable to a wide audience. Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator.
Either way, we're going to help you get your home water-ready. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Again, the kit's instructions will tell you how to do this. This is feature allows you to search the site. After installation, dating a hot guy check the water pressure by dispensing water.
How to Connect a Refrigerator Water and Ice Dispenser
How to Hook Up a Water Line to a Refrigerator From the Sink
Connect and install the water line to your refrigerator. Please contact us via Live Chat for a faster response. Although the braided steel is considerably more expensive, the extra strength it provides is well worth the investment. Insert the new water line into the opening on the tee.
This supports the Maven widget and search functionality. Keep in mind that you will need a compression nut at both ends, and some kits only come with one. Braided stainless steel tubing is the option I recommend.
Find your water supply lines beneath your sink. The only problem I see with using copper is that it can kink easily. Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel.